BOSER Technology Industrial Single Board Computer HS-6038 Especificações

HS-6038 Socket 370 133MHz FSB Industrial Single Board Computer •Full-size•All-in-One•CompactFlash• •133MHz FSB•CRT•Dual LAN•Audio• •ATA/33/66/100•RS-2

41.3 Board Dimensions

5Chapter 2 Unpacking 2.1 Opening the Delivery Package The HS-6038 is packed in an anti-static bag. The board has components that are easily damaged

6It is recommended that you keep all the parts of the delivery package intact and store them in a safe/dry place for any unforeseen event requiring t

7Chapter 3 Hardware Installation This chapter provides the information on how to install the hardware using the HS-6038. This chapter also contains i

83.2 Board Layout

93.3 Jumper List Jumper Definition Setting Page JP2 Host Bus Clock Rate Select: 133MHz FSB Open 10 JP3 Clear CMOS: Normal Operation Short 1-2 15

10Connector Definition Page PC1 / PC2 PC/104 Bus 64-pin/40-pin Connectors 22 USB1 External USB Connector 15 USB2/USB3 Internal USB Connectors

11 CN9: I2C Bus Connector PIN Description 1 SMBDATA 2 SMBCLK 3 GND 123 3.8 IDE Drive Connector IDE1/IDE2 are standard 40-pin connector daisy-cha

123.9 Floppy Disk Drive Connector The HS-6038 uses a standard 34-pin header connector, FDC1, for floppy disk drive connection. A total of two floppy

13 CN12: RS-422/485 Connector (5x2 header) PIN Description PIN Description 1 TX- 2 TX+ 3 RX+ 4 RX- 5 GND 6 RTS- 7 RTS+ 8 CTS+ 9 CTS-

Copyright Disclaimers The accuracy of contents in this manual has passed thorough checking and review before publishing. BOSER Technology Co., Ltd.,

143.12 Ethernet Connector The HS-6038 provides one dual RJ-45 10/100 Based LAN interface connectors. Please refer to the following table for their id

153.14 USB Connector The HS-6038 provides one 4-pin external USB connector at location USB1, and two 8-pin connectors at locations USB2 and USB3. 

163.16 Power and Fan Connectors The HS-6038 provides one 5-pin ATX Power On connector at CN10, one 2-pin ATX Power ON switch at CN6, and a single 3-

17CN8 onboard HS-6038 is a 3-pin fan power output connector.  CN8: Fan Power In Connector PIN Description 1 GND 2 +12V 3 FAN In 1 13GND+12VFA

18CN1 and CN7 are the Keylock and Reset Button connectors onboard.  CN1: Keylock Connector PIN Description 1 VCC 2 N/C 3 GND 4 Keylock 5 GND 12

193.21 Audio Connectors The HS-6038 has an onboard AC97 3D audio interface. The following tables list the pin assignments of the CD-ROM Analog Input,

203.23 Watchdog Timer Once the Enable cycle is active, a Refresh cycle is requested before the time-out period. This restarts counting of the WDT per

21 MOV DX, 2EH MOV AL, AAH OUT DX, AL * User can also use AL, 00H’s defined time for reset purposes, e.g.00H for Disable, 01H = 1sec, 02H = 2se

22Inserting a CompactFlash card into the adapter is not a difficult task. The socket and card are both keyed and there is only one direction for the

23 PC2: PC/104 Bus 40-pin Connector PIN Description PIN Description 1 GND 21 GND 2 MEMCS16* 22 SBHE* 3 IOSC16* 23 LA23 4 IRQ10 24 LA22 5

Table of Contents Chapter 1 General Description…………………...1 1.1 Major Features... 2 1.

24 PC1: PC/104 Bus 64-pin Connector PIN Description PIN Description 1 IOCHECK* 33 GND 2 SD7 34 RESETDRV 3 SD6 35 +5V 4 SD5 36 IRQ9 5 SD

253.26 DiskOnChip Address Setting The DiskOnChip function allows the system to boot or operate without a FDD or a HDD. DiskOnChip modules may be f

26Pin 1LocationDiskOnChip 4. The installation is now complete and your module is now ready for use. NOTE: If you encounter difficulty installing yo

27Chapter 4 AMI BIOS Setup The HS-6038 uses AMI BIOS for the system configuration. The AMI BIOS setup program is designed to provide the maximum flex

284.2 Using Setup In general, you use the arrow keys to highlight items, press <Enter> to select, use the <PageUp> and <PageDown> k

294.3 Main Menu Once you enter the AMI BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from seve

304.4 Standard CMOS Setup The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard

314.5 Advanced CMOS Setup This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s

324.6 Advanced Chipset Setup This section allows you to configure the system based on the specific features of the installed chipset. This chipset m

334.7 Power Management Setup The Power Management Setup allows user to configure the system for saving energy in a most effective way while operatin

Chapter 4 AMI BIOS Setup……………………..27 4.1 Starting Setup ... 27 4.2 Using Setup...

344.8 PCI / Plug and Play Setup This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system that allo

354.9 Peripheral Setup The IDE hard drive controllers can support up to two separate hard drives. These drives have a master/slave relationship that

364.10 Hardware Monitor Setup AMIBIOS SETUP – HARDWARE MONITOR SETUP (C)2001 American Megatrends, Inc. All Rights Reserved CPU Temperature Detected

374.11 Auto-Detect Hard Disks This option detects the parameters of an IDE hard disk drive, and automatically enters them into the Standard CMOS Set

384.12 Change Supervisor/User Password AMIBIOS HIFLEX SETUP UTILITY – VERSION 1.52 (C)2001 American Megatrends, Inc. All Rights Reserved HS-6038LV V

39When a password has been enabled, you will be prompted to enter it every time you try to enter Setup. This prevents an unauthorized person from ch

404.14 Optimal Configuration with Fail Safe Settings When you press <Enter> on this item you get a confirmation dialog box with a message simi

414.15 Save Settings and Exit Pressing <Enter> on this item asks for confirmation: AMIBIOS HIFLEX SETUP UTILITY – VERSION 1.52 (C)2001 America

424.16 Exit Without Saving Pressing <Enter> on this item asks for confirmation: Quit without saving (Y/N)? Y This allows you to exit Setup wi

43Chapter 5 Software Utilities This chapter contains the detailed information of IDE, VGA, LAN and Audio driver installation procedures. The utility

Safety Instructions Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge,

442. Click on the INTEL_ICH2 button to continue. 3. When the IDE \ INTEL_ICH2 box appears on your screen, click on the INTEL_R&HIPSET_SOFTWARE_

454. Immediately after clicking the IDE button in Step 1, the pr ogram launches the InstallShield Wizard that will assist you in the installation

466. When the Readme Information dialog box pops up, just click on the Next button to proceed. 7. Once the InstallShield Wizard finishes updating

475.1.2 Installing Intel Security Driver 1. Following Steps 1 ~ 3 of the Intel 815 chipset software (from the preceding section), click on the INTE

483. When the Release Notes box pops up on the screen, read through any important information listed before clicking the Next > button. 4. Setu

495. Once the setup program finishes copying files into your system, it will prompt you to restart the computer. Tick on the Yes, I want to restart

502. When the VGA main utility window is displayed. Select INTEL_815 to continue. 3. The INTEL_815 window shows up next. Select WIN9X to invoke t

514. The program launches an introduction screen of what graphics driver it will install. Close all other running Windows applications then click on

526. The VGA driver utility program starts copying files needed by your Win98 to invoke the VGA capabilities. Once finishes, the system will prompt

532. The program launches the InstallShield Wizard for Intel 810/810E/815/815E/815EM chipset graphics. Close all other running Windows applications

545.2.3 Win NT4.0 1. Follow steps 1 and 2 from the Win9x installation procedure. When the INTEL_815 window shows up, select NT40 to invoke the inst

555.3 LAN Driver Installation 5.3.1 Win 95/98 1. Right click on My Computer icon then scroll to the Properties item from the pop-up menu. 2. Select

563. Once the PCI Ethernet Controller Properties screen pops up on the screen, click on the Update Driver … button to launch the Update Device Drive

57 5. The wizard program will then require you to specify the location of the driver file. Tick on the Specify a location: and type or select the pa

58 6. The program now starts copying the file(s) needed by your Win98. When t he progr am fai ls to seek fo r 8255x Del. exe fi le f rom your spe

59 8. When the program finishes updating and copying files for the Intel Pro/100VE Network Connection, click on the Finish button to proceed. 9. F

60 5.3.2 Win 2000 1. Right click on My Computer icon and then scroll to the Properties item from the pop-up menu.

612. When the System Properties window pops up on the screen, click on the Device Manager button. 3. A list of all devices installed appears, scr

624. Once the Ethernet Controller Properties screen pops on the screen, click on the Update Driver … button to launch up the Update Device Driver Wi

636. The wizard will then inform you the unknown device it detected from the system. Since the Win2000 driver list does not include Intel chip drive

1Chapter 1 General Description The HS-6038 is a 133MHz FSB Intel® 82815/82801BA chipset-based board designed for PICMG Bus Celeron™/Coppermine™/Tual

648. The wizard program will then require you to insert the manufacturer disk at your specified location (entered at the Copy manufacturer’s files

6510. When the program finishes updating and copying files for the Intel Pro/100VE Network Connection, click Finish to proceed. 11. For the new ha

662. The Network Configuration dialog box then appears, notifying the user that there is no Windows NT Networking available. Click on the Yes butto

674. The succeeding screen then indicated that the wizard will initially search for Network Adapter from the available list of drivers. Select on St

686. The wizard program will then require you to insert the manufacturer disk and specify the location of the driver file (i.e., c:\i82562). Click

698. The wizard program now displays on the screen that it has detected the Intel() PRO Adapter. Click on the Next > button to continue installin

7010. The next screen will allow you to customize the Network Services the wizard program intends to install. Tick services as needed and then clic

7112. The Network Setup Wizard will then need to copy the drive file(s). Specify the path of your device driver(s) (i.e., d:\i386) and click the Con

7214. If you need to disable network bindings on the network services installed, select the service and then click on the Disable button. Otherwise

7316. The wizard program then informs you that Networking is now installed on your system. You must restart your computer to make the setting change

2Additional onboard connectors include an advanced USB and IrDA ports providing faster data transmission, and a dual RJ-45 connector for 10/100 Based

745.4 Audio Driver Installation 5.4.1 Win 95/98 1. After loading the Utility CD-ROM, the program automatically runs the utility. Press Enter to pr

75 3. Select the language you intend to use for the installation. The default is English. After making your choice, press on the OK button to procee

76 5.4.2 Win 2000 1. Following steps 1 and 2 of the Win95/98 AC97 installation, select WIN2K button when the ALC100 dialog box appears on the scree

77 4. Once the InstallShield Wizard completes the operation and update of your AC’97 driver, it will ask you to remove any disks from their drives,

785.4.3 Win NT 1. Following steps 1 and 2 of the Win95/98 OR step 1 of Win 2000 AC97 installation, select WINNT button when the ALC100 dialog box a

794. Once the InstallShield Wizard completes the operation and update of your AC’97 driver, it will ask you to remove any disks from their drives, a

80This page intentionally left blank.

31.2 Specifications  CPU: Socket 370 for Intel Celeron/Coppermine/Tualatin 800MHz ~1.2GHz CPU  Bus Interface: PICMG Bus  Memory: Two DIMM sock